Post by mark8 on Dec 2, 2013 14:50:10 GMT
This is not a definitive way to rig the Cuda, but just the way that I have done it which may be a useful reference.
The Cuda 14 has been the easiest yak that I have owned to rig out ready for fishing. This is because so much thought has gone into the design and extra's that there is very little left for the yak angler to do before the first launch.
What it comes with.
The amount of extras that come as standard on the Cuda is really impressive. The 2013 edition comes with an insert in the centre hatch which acts as a tackle tray or fish storage depending on your needs.
There is also an additional circular cut out in the centre hatch that allows easy access to this area without having to remove the full hatch.
The 2013 centre hatch also has tracking already attached to it and comes complete with a ball mount fitting and rod holder. This tracking will accommodate a variety of yak attack fixtures and fittings.
Behind the seat there are two rocket launcher style rod holders. Again in the new version these are click lock style fittings allowing the holders to be pointed in any direction if you are trolling or vertical if you are just stowing rods.
For those with cameras there is already a Go Pro mount fitted
What you need to do.
There are two things you need to do to the Cuda before your first fishing trip, fit an anchor trolley and fit the fishfinder.
Fitting the fish finder couldn’t be easier. I have fitted mine to the left hand side and just attached it with four self-tapping screws.
There has been no need to drill holes for the cables as they can just run under the front hatch without distorting it and causing water to come through.
The transducer is just siliconed to the hull
I like to use silicon so that if I change yaks I can easily remove the fish finder to put on the new boat.
To fit an anchor trolley is also simple. I bought a complete kit from www.kayakfishingshack.co.uk
The good thing about the Cuda is that you can access the inside from the front and back. So simply bolt one pad eye at the front, and one at the rear.
Fix the pulleys to the pad eyes using a short length of bungee cord. Then run the para cord through the pulleys and use the carabiners and ring to complete the circle
I tend to use oversized carabiners but that is just personal choice. Screw in the cleat near the seat and the job is done.
The only addition I make is the front rod rest. I mainly do bait fishing and like to have the rods in front so have adapted this set up on every yak I have owned.
The rest is a Preston Innovations Dutch feeder arm, the longer version. Take a bank stick, cut to length and flatten it. Drill a hole and use the existing bolt on the rod holder to secure it. You may need a cable tie just to hold it in place.
That’s it.
Not a definitive guide but what I did before my first launch. The whole job took less than twenty minutes and has been tested in the Humber and Filey Brigg without issue. This has turned out to be the most comfortable fishing platform that I have had on a kayak and I can’t wait to use it to its full potential in the coming year.
The Cuda 14 has been the easiest yak that I have owned to rig out ready for fishing. This is because so much thought has gone into the design and extra's that there is very little left for the yak angler to do before the first launch.
What it comes with.
The amount of extras that come as standard on the Cuda is really impressive. The 2013 edition comes with an insert in the centre hatch which acts as a tackle tray or fish storage depending on your needs.
There is also an additional circular cut out in the centre hatch that allows easy access to this area without having to remove the full hatch.
The 2013 centre hatch also has tracking already attached to it and comes complete with a ball mount fitting and rod holder. This tracking will accommodate a variety of yak attack fixtures and fittings.
Behind the seat there are two rocket launcher style rod holders. Again in the new version these are click lock style fittings allowing the holders to be pointed in any direction if you are trolling or vertical if you are just stowing rods.
For those with cameras there is already a Go Pro mount fitted
What you need to do.
There are two things you need to do to the Cuda before your first fishing trip, fit an anchor trolley and fit the fishfinder.
Fitting the fish finder couldn’t be easier. I have fitted mine to the left hand side and just attached it with four self-tapping screws.
There has been no need to drill holes for the cables as they can just run under the front hatch without distorting it and causing water to come through.
The transducer is just siliconed to the hull
I like to use silicon so that if I change yaks I can easily remove the fish finder to put on the new boat.
To fit an anchor trolley is also simple. I bought a complete kit from www.kayakfishingshack.co.uk
The good thing about the Cuda is that you can access the inside from the front and back. So simply bolt one pad eye at the front, and one at the rear.
Fix the pulleys to the pad eyes using a short length of bungee cord. Then run the para cord through the pulleys and use the carabiners and ring to complete the circle
I tend to use oversized carabiners but that is just personal choice. Screw in the cleat near the seat and the job is done.
The only addition I make is the front rod rest. I mainly do bait fishing and like to have the rods in front so have adapted this set up on every yak I have owned.
The rest is a Preston Innovations Dutch feeder arm, the longer version. Take a bank stick, cut to length and flatten it. Drill a hole and use the existing bolt on the rod holder to secure it. You may need a cable tie just to hold it in place.
That’s it.
Not a definitive guide but what I did before my first launch. The whole job took less than twenty minutes and has been tested in the Humber and Filey Brigg without issue. This has turned out to be the most comfortable fishing platform that I have had on a kayak and I can’t wait to use it to its full potential in the coming year.
